Peugeot 208 Key Replacement

Peugeot 208 key replacement should be left to experienced auto locksmiths who have the right equipment and technical knowledge. They will be able to make and program new keys faster than a dealership would and at a lower price.

A dead battery for your coin is most likely to blame the reason your key-fob stops locking or unlocking doors. But, there are other reasons the key could be malfunctioning.

Dead Coin Battery

A dead coin battery will stop your Peugeot 208 from locking and unlocking, and also hindering it from starting the engine. In this scenario you'll need choose the alternate method to start that is described in the owner's manual.

Another reason your 208 might not start is that the spark plugs are been damaged. The spark plugs ignite fuel to start the engine. However they are limited in their lifespan. They will eventually break down in the event that they aren't utilized enough.

There is a straightforward solution to this problem. Verify the voltage of your battery using a multimeter. If it's lower than 11.5 volts, then you need to replace it. It is also important to clean the battery's contacts if it has corrosion. This can be done by removing the rubber covers off the two terminals of the battery, and then using a wirebrush, you can remove any corroded parts of the battery. Then, reconnect the positive pole cables to the negative.

Water Damage

If your 208 will not start and the battery hasn't failed, you should inspect the spark plugs. It could be that they're overly dirty, causing them not to spark. The spark plugs can be cleaned in a workshop.

Peugeot cars use a key with a transponder that is compatible with the immobiliser. This ensures that only the right key is able to turn the engine. If the chip inside the Peugeot key is damaged then it will not send the correct signal to the vehicle.

This is a very common issue that can be caused by water damage. This is a frequent issue in warmer climates where the vehicle is exposed to snow or rain. In this instance, you should contact an experienced locksmith who has the required tools and equipment to reprogram the key. They will also have all the latest technology and machinery required to make a Peugeot smart key. The process should take no more than 15 minutes.

Contacts to the battery are not working properly.

Peugeot changed from the carbon-encased transponder chips and introduced a new kind of chip that utilizes electronic components on circuit boards. This new system works well when it's brand new, however, over time, the circuit boards start to degrade and stop working properly.

This can prevent the immobiliser chip activating the immobiliser chip, causing your car not to start. Contact a Peugeot specialist, or a locksmith if this is the situation.

Another issue that is common is when the battery in the key fob gets depleted, which causes the key blade to stop from entering the lock. A car locksmith will replace the battery, and then cut a fresh blade for you. This is a quick solution.

Faulty Receiver Module

It could be that the receiver module is defective in the event that your Peugeot key fob fails to function after being dropped on the floor, exposed to a sudden downpour or accidentally washed. The receiver is responsible for sending radio frequency signals to an on-board computer, which is responsible for controlling the centralized locking system of your Peugeot vehicle.

The key fob itself has rubber seals that prevent water from getting to the electronic chip inside. However, prolonged exposure to water can penetrate these seals and damage the chip. Submerging the key fob into the ocean at the beach or throwing it into the water can be particularly damaging due to the high salt content.

If your peugeot key replacement spare key fob isn't working You'll need the module replaced. This is only completed by an experienced auto locksmith or Peugeot specialist. Unlike other cars, Peugeot keys are protected by a unique immobilizer system that requires the correct programming in order to start the engine. This is the reason that you should only rely on the Peugeot locksmith to create and program an alternative.

Computer with a problem on board

The computer on the board of your Peugeot is responsible for a number of the systems in the car, from power windows to the airbags. If something is wrong with these systems, they will usually display a code that identifies the issue. The code will be stored within the system until the issue is fixed. In most cases, this will require replacing the onboard computer.

One of the most frequent reasons for the light turning on is the loose or corroded connections within the airbag sensor. It can be due to wear and tear, aging or exposure to moisture and salt. It is imperative to have this issue addressed as quickly as you can, as an airbag that is not functioning properly could be risky in the event of an accident.

If you see the error "card not found" on your Peugeot key fob, the battery inside the key fob could be dead or weak. This can prevent the key fob from sending a signal to disable the standard immobilizer in your vehicle. Test this by pressing the unlock key on the fob's key and then trying to start your car. If this doesn't work then the battery in the key must be replaced.