Double Glazing Door Lock Repairs

Is your uPVC window or door mechanism broken? Perhaps the handles on your uPVC windows or doors aren't aligned correctly or are difficult to operate.

It is crucial that the double glazed doors work smoothly, otherwise you'll lose energy and increase the chance of burglary. Owen the Locksmith can repair your door lock at an affordable price.

Snapped Key

It can be quite frustrating when a key is snapped inside a lock. It also poses a security risk since the door may not be locked and could leave you open to intrusion. There are a few quick fixes you can try to resolve the issue and get your door working again.

Keep calm. If you panic and start doing a lot of fumbling around you may end up pushing the broken piece of the key deeper into the lock, making the situation worse.

Spray WD-40 or another penetrating oil, into the lock. This will assist the broken piece emerge more easily. You can also use the screwdriver to break off any pieces stuck. If you're lucky enough to have a little bit of the key left sticking out, you can make use of a paperclip or other thin metal object to grab it and then pull it out. Both of these methods work well, but be very careful not to push the damaged piece of the key deeper into the keyway.

Some paperclips have grooved edges that could work in a pinch as a hook extractor and some jigsaw blades are also suitable for this purpose. If you don't have any of these items, you can bend a hook using needle-nosed pliers. Also, a pair tweezers is a good way to grasp and pull out the last piece of the key that was broken.

If you are unable to remove the broken key piece, use a lock deicer. It's usually found in most hardware stores. It works by freezing any water or ice that could be inside the lock.

If none of these solutions seem to work, it could be time to contact a locksmith. Fitlocks experts can quickly fix issues such as broken handles and snapped keys with upvc window repairs locks and door mechanisms. They can also alter the double glazing door mechanisms to ensure that they are simpler to operate. Get a double glazing repair via our website, or give us a call to discuss your needs.

Broken Cylinder

A damaged cylinder could pose a serious security risk. It's a good thing that it's a simple repair for an expert locksmith to complete. To fix the cylinder locksmiths must tap it. This can be done using a hammer, or any other tool. The best method is to make use of a wire or a long match. Place the match or wire's end close to the keyway. The locksmith can strike the lock and break it open. This is much better than using a heavy hammer, which could damage the lock.

Overheating is the primary reason for cylinder heads to crack. This can happen when the cylinder head and block are made of various metals such as cast-iron and aluminium. When various metals heat up and cool down at different rates, it may cause localised hotspots that expand faster than the rest of the cylinder head, thus leading to cracks.

Another possible cause for cracks in cylinders is corrosion. When the cylinder head and cylinder block are not properly maintained, this can lead to rusting or corrosion, which may cause them to expand at a greater rates than they should. As time passes, this may also lead to cracks.

If your uPVC window or door lock is stiff or requires an enormous amount of pressure to turn, this could be due to several things. A faulty locking mechanism, misalignment, or a worn handle are common causes of this issue.

Fortunately it is a simple and cost-effective fix for the majority of homeowners with double glazing. A professional locksmith should be able to solve this issue within a matter of hours after arriving at your residence. They can replace the locking mechanisms, or replace the window handles and replace the gearboxes, depending on your particular requirements. A professional locksmith will be able to provide you with a recommendation of the most cost-effective solution for your home. They can also suggest upgrades to high-security 3 Star euro cylinders TS007 that add an extra layer of security against burglars. It's a small price to pay for the peace-of-mind that comes from knowing that your uPVC door is secured.

Broken Handle

window replacement near me handle locks have intricate mechanisms that deteriorate with time and use, so it's not a surprise that they sometimes break. It can be difficult to determine the cause of the problem and then fix it properly.

If the issue is with the internal locking mechanism or the latch, fixing the broken handle can improve your uPVC double glazing door's security and allow you to stop draughts. It is costly to repair or replace your handle if it is not done correctly and could also harm the frame and lock of your door.

Screwdriver: With the window open remove the screw that holds the handle. The screw should be located on the inside of the backplate. It is typically concealed by a screw cap for aesthetic reasons. You should not be able to replace any internal parts of the handle such as the levers and plates on either side. Ideally, keep these in the same order so you can re-install them in the event of a need.

Next, turn the handle until it's 90 degrees to the window frame and loosen the screw at the back of the handle that fixes it to the internal spindle with a second screwdriver. Once this is released, you'll be able to pull the handle off and pull out the broken spindle. Replace it with a brand new spindle, ensuring it's the same length (you can purchase them online or in hardware stores). Screw it into place. Be careful not to overtighten because this could cause damage to the handle or the window frame.

Check that the new handle is correctly fitted after which you can close and test the handle. It is likely that it will operate smoothly and you'll be able open your window again.

While you're working on the handle, be sure to check your uPVC windows are shut properly. If they don't close properly, you could experience draughts or damp in your home. Also, you could be compromising the energy efficiency of your home. A local window company, such as Core Sash Windows, will be in a position to adjust the hinges on your window frames to ensure they are able to shut properly.

Broken Spindle

It is often the case that the spindle in the handle is broken, not the handle itself. This is most typical in uPVC tilt and turn windows. These types of windows require a handle which operates a locking mechanism in the window frame. The handle is connected to a centre rod that triggers a set of cams that look like mushrooms, they secure the frame of the window. If the dead latch mechanism does not open when the handle is turned, it is likely that the spindle is broken, this can be a frustrating problem.

Luckily, there are steps that can be taken to rectify this issue. A good locksmith can quickly and efficiently solve the issue. A good locksmith will be able disassemble the handle of the window by using a tool to remove the wheel part that houses the spindle. This can be done without damaging the handle or causing other damage to the frame of the window.

Once the wheel has been removed the technician can then inspect the spindle to determine what caused it to break. This involves breaking down the spindle into its component parts and meticulously noting their general condition as well as any particular areas of wear or damage. This process is typically done in a clean environment by highly skilled technicians.

The next step is to clean the damaged spindle. This will help get rid of any dirt or other debris that may be obstructing it from working normally. After that, the spindle can be repaired or replaced. If it is replaced, the technician will need an identical dowel size to the one used in the first and drill mating holes in both pieces of the spindle. This ensures that the new spindle is an exact fit with the handle.

If the spindle is damaged and cannot be repaired, it might require replacement completely. Home centers sell generic replacements but If the style of your window is unusual then it is necessary to find a woodworker or cabinet maker who can duplicate the exact component for you. Once the new spindle is installed, it can be attached to the handle by lining up the holes for screws in the handle with the frames existing screws. Once the new handle is installed, you are now ready to operate your uPVC window.