UPVC Window Handle Replacement

Replacing a damaged or broken window handle is a relatively simple process and with the right tools it can be accomplished quite quickly. It's important to know what kind of handle you have and the spindle's size before you purchase the replacement.

Older uPVC windows use handles with cockspurs, which have spurs that protrude to secure a wedge-shaped cockspur striker plate. These can be right-handed or left-handed and should match when replaced.

What kind of lock or handle do you have? I have

There are many different types of window handles made of upvc and locks, each with their distinct advantages and functions. The type of handle that you have will determine if your locking mechanism is efficient and if it's easy to open the windows. As time passes and with regular usage, the window handles made of upvc can become damaged or worn out, rendering them less secure and efficient. In some cases, they may even be completely removed. It is essential to fix your window handles made of upvc immediately if you begin to notice they are falling off. This will help prevent potential break-ins and ensure your home is secure.

The good news is that replacing your window handles made of upvc is a relatively simple task that can be completed by everyone. You'll need some basic tools, but with the appropriate knowledge, it's an easy task that will only take a few minutes. You will need to be aware of the type of handle or lock that you have on your window. This will help you choose the correct replacement.

Inline Espagnolette Handles

They are the most popular kind of upvc handle and are usually located on the other side of your window. They are flat and have a latch which engages the locking mechanism of the window frame. Inline upvc handles also have a spindle that runs through the middle of the handle and then into the frame of the window to activate the latch.

Cockspur Handles

They are typically found on older uPVC window frames. They have a distinctive, hook-shaped design. Cockspur handles are held to the window frame by only one screw and are less secure than other kinds of window handle.

Handles that turn and tilt

As opposed to the other handles made of upvc, tilt and turn handles can be turned to open the window, and tilted inwards to allow ventilation. In general, they have a 7mm spindle at the back of the handle and are available in both left and UPVC Window Handle Replacement right handed versions.

It is crucial to determine the size of the spindle when purchasing a new upvc handles. Not all of them are the exact same size. To determine the length of your handle made of upvc, simply drop something in the middle of the hole, and then measure the distance it travels before it comes into contact with an obstruction. This is the maximum spindle size that will fit into your windows.

What is the spindle?

uPVC window handles work in a similar manner as doors. By turning the handle, you will be able to operate a latch within the frame. The latch opens the window, so that it can be closed and opened. The handles could be damaged, especially if often used or are exposed to harsh environments. This can leave you needing to replace your uPVC handles for windows as they might not operate the window in a proper manner for a long time.

There are many different kinds of uPVC handles that are available, including Espag, Cockspur and Spaded handle options. These handles are designed in a variety ways to fit into uPVC frames. Each handle type uses an entirely different spindle for locking the window mechanism. It is essential to determine the type of handle installed on your uPVC windows to ensure that you replace it with the correct one.

The base of the handle will inform you what type of upvc replacement window handles it is. A snap-in covers should be over the screw that holds the handle's base in position. Remove this and then you should be able see the second holding screw at the opposite end of the base section of the handle. Once both screws have been removed then you should be able to take the handle out of the uPVC.

After you have removed the uPVC handle, carefully unscrew it from the locking mechanism. Take note of the length of the spindle. You'll need to buy a replacement of the same length as the original handle and locking device.

The primary issue with uPVC window handle problems is that the spindle gets worn out and can no longer operate the locking mechanism. This could be due damage from constant use, a loosening of the locking mechanism, or even corrosion that occurs over time. If this occurs, it will be necessary to replace the window handle and locking mechanism to restore full functionality to your uPVC windows.

How do I take off the handle that was previously attached?

Window handles are susceptible to being damaged or broken over time. It is essential to repair them as quickly as possible to ensure your safety. It is simple to replace a damaged or worn handle. The task can be completed in under one minute without the need for special tools.

To take off the handle, you first need to remove the screw that is located at the bottom of the handle. Once the screw is removed, the handle can be pulled away from the base section. There is another screw located at the bottom of the handle base, and it is able to be removed as well. Once the two screws are removed, the handle can be removed from the base of the window.

Once the old handle is removed, grab the new handle and line up the fixing holes with the holes that are currently in the window frame. There may be a tiny sticker or caps on the new handle, so take them off these if necessary and then put the handle in its place. Once the handle is in place, it is crucial to verify that it is working by turning the handle and ensuring that the lock mechanism activates.

Espag handles come with an elongated spindle that extends from the handle and slot into a multipoint locking mechanism in the frame of the window. Cadenza windows come with a blade with cutouts that are incorporated into the lock mechanism. Cockspur handles are long and are hung over the frame of the window or the transom crossmember of the bar.

Once you have the new handle in place, slide the spindle inside the window lock and then tighten it. Replace the snap-in cover and screw cap (if appropriate) once the handle is fixed. When the handle is ready to use, you can open and close the window a few times to make sure that it functions correctly and securely.

How do I put in the new handle?

It's not that difficult to change the handle on your Upvc windows. The process is very simple. All you need is a screwdriver, and a bit of patience. First, ensure that the old handle is unlocked. Then, remove any screws visible. You can also replace them with screw caps. After removing the handle, you'll need to record the length of the spindle which extends from the back. This is important as it will determine the type of handle that you will require to purchase.

Espagnolette handles made of uPVC are the most popular kind of handle. The spindle runs through the handle to activate the locking mechanism inside the frame of the window. Once the handle is turned it opens the latch on the window, allowing it to open. When used regularly and over time, espagnolette handles may be damaged.

Cadenza handles are a second type of uPVC window handle, which is typically used on tilt and turn windows. They feature a protruding knife that is operated by a multi-point locking mechanism inside the window. They are generally more secure than espagnolette handles since they are only accessible from the inside. You can replace them with the same method as you would for espagnolette handles however, ensure that the new handle is angled, not flat.

Once you have decided on the right handle for you, you can simply line up the new handle with the existing screw holes and then screw it in place. After that, you should put the screw covers back on and verify that the new handle is working properly. You can accomplish this by moving the handle between the locked position to the unlocked one for a few times. If you encounter any issues, it may be worthwhile contacting a professional to see if they can assist you in solving the issue. They can offer advice on how to solve the issue in a quick and efficient way.