Repairs to uPVC Windows

uPVC is an excellent choice for modern homes. They are long-lasting, durable and easy to maintain. In contrast to aluminium and timber, they are not susceptible to corrosion or rot.

It is important to clean and oil UPVC windows and doors regularly. This will prevent unnecessary repair costs as well as improve the efficiency of energy.

1. Broken Glass

If the glass in your window is broken it can cause a great deal of damage to your home, which can make it very hazardous and possibly fatal. It is important to make sure that your windows are in good condition.

Single-pane windows are relatively simple to replace and will usually fit into the old frames very easily. However, if you have double-pane windows that are anchored by internal beading, it'll be more difficult to remove the existing panes and install new ones. In this instance it is essential to buy plastic spacers to help the new pane fit into the window frame.

If you plan to attempt to remove the glass panes yourself, it is essential to wear the proper safety gear such as gloves that are thick and eye protection. It is also recommended to lay down a drop cloth before you begin working on the window panes so that any shards of glass fall onto the fabric and not on the floor and could be trampled.

It's a great idea to cover the gap with tape after the glass has been removed. This will prevent water and drafts from entering your home until a professional comes out to repair the window. This will also provide an obstruction to prevent intruders from making their way into your home. If the distance between the window and the door is significant, you may prefer an alarm system that has an opening. This will give you the best of both.

2. Sagging

uPVC windows and doors are a low-cost energy-efficient, durable and long-lasting alternative to timber sash windows. In time, they could be affected by a variety of issues such as sliding. A sagging uPVC window can cause problems with light, draughts, and even security. If you notice that your uPVC window is beginning to sag it's important to act quickly to prevent the problem from worsening.

To fix a window that is sagging you can try repositioning the hinges. First, you'll need to unblock the windows to access the frame. Then, you can remove the hinges on the top and bottom with a screwdriver and adjust the hinges clockwise or counter-clockwise. Once you've adjusted the hinges, close the window and check for fitting. If you're satisfied with the fit of the window, you can tighten screws to hold them in place.

If you can't reposition the hinges, you might require replacing the seal. Rubber seals may dry out and lose their elasticity over time, causing them to loose their elasticity. If this happens, it's essential to replace the seal as fast as you can to ensure that your uPVC windows are waterproof and secure from draughts.

uPVC handles may also become loose. This is usually due to screws that have become undone over time, but it can also be caused by the handle mechanism getting worn out. It's relatively simple to fix a loose uPVC handle. First, you'll need close your window and do a test fit. The joints at the corners of the sash should be aligned with the joint on the casing. If it does not you can use a screwdriver to loosen up the handle. Then, you can turn the mechanism to position.

3. Water Leaks

It is essential to act if you get up each morning to find mouldy walls and wet floors. Water leaks through windows can cause structural damage to your home and impact your ability to regulate the temperature of your home. Most often, uPVC window Replacement Near me leaks are caused by a damaged or missing sealant.

This is an easy fix that can be accomplished by any DIYer who is competent. Depending on how severe the problem is, the old caulking may have to be removed. When it comes to uPVC repair, you should be careful not to over-caulk. This will only make your window more difficult to clean and decrease its energy efficiency.

Make sure that the drainage holes do not have debris inside them and that the sill pan is angled correctly to drain away from the window. In more serious situations, you may have to replace the window.

Moldy sills and rotten ones are also signs of water leakage. The fungus thrives in conditions of dampness and can spread quickly throughout the house.

It is also important to keep in mind that if the leakage originates from the glass of your double glazed windows, it is more likely to be a problem with the glass seal, rather than the frame or sagging. It is also possible to be corrected by an uPVC window doctor specialist who can replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are difficult to open, or are loose and blow open with ease, it may be hinges that are at fault. They can be replaced by any competent DIYer and can usually be completed in just a few minutes.

Like any mechanical component, hinges can wear out over time. It is essentially a simple process but it can be simpler with someone else to assist in holding the frame in place.

It is also worth checking that the uPVC hinges are opened and closed in the correct direction. You can check this by looking for the arrows on each hinge, this indicates the direction in which the window should open.

Faulty window hinges can be caused by incorrectly opening the window in a particular way or by inadequate installation at the factory. Sending us a photo via our website will often resolve the problem. We are happy to offer advice.

Regularly lubricating the hinges is essential. This can be accomplished by applying a light engineering oil on the hinges. We recommend using a solvent-free lubricant such as the 3-in-one Multi-Purpose oil. Regularly lubrication makes the window easier to open and close. It also helps prevent corrosion and decrease the chance of sticking. The ideal time to perform this every year. WD40 and other solvent-based lubricants are not recommended as they will damage parts of your uPVC window.

5. Draughts

Draughts can be caused by a variety of different factors. The hinges may also become unbalanced due to wear, causing a gap where the sash and frame meet. If they are damaged beyond repair, it may be required to realign them. Second, the interlock can also become misaligned. It is located on the hinge's side, and might require to be cleaned. In some instances it is possible to replace the hinges.

The next common reason for draughts are the window seals. They can become worn down or damaged over time and will allow air to escape through the gaps. This can be prevented by replacing them with high-quality weatherstripping. Replace the upvc windows with low-emissivity lenses. This will help regulate indoor temperatures, and reduce draughts.

Lastly, one of the most effective ways to cut down on the draughts in your home is to use an draught excluder. These are usually fabric tubes that are filled with some type of filler. They can be positioned on the top of your windowsill. They can keep your home warm by blocking out cold air.

Your upvc windows can continue to provide excellent insulation and security in your home with a little regular maintenance and repairs. It is crucial to recognize that windows last for a certain period of time and eventually, they will reach an point at which it is more economical to replace them than repair them. If you have any problems with your upvc window you should consult a professional immediately.