Reasons Why Your nissan key replacement Qashqai Key Fob Won't Work

The Qashqai has a distinct SUV feel due to its larger dimensions, and the wheel sizes of 19 inches in Ti and ST-L models can be a bit spongy at times. The front tyres of Qashqai could also lose grip on rough surfaces and its CVT can occasionally display wrist-flexing torque steering.

It is usually due to an unresponsive battery that can be replaced in a matter of minutes. Make sure that the replacement battery is of the same voltage, size and specification.

Water Damage

One of the main reasons a Nissan key fob might display the "key ID is not correct" message is due to water damage. The rubber seals on the key fob shield the chip's electronics, but prolonged exposure to moisture can cause it to malfunction effectively. It's normal to see this if your key fob was dropped in the ocean or swimming pool. It can also occur when it is wet from rain or soapy hand.

If your key fob was exposed to water over an extended period of time and you're not sure, clean it with isopropyl, or an electronic cleaner. It may also require taking to a specialist for repair or replacement.

If your key fob need to be replaced, the procedure is relatively easy. First, make sure that you have a multipack of the correct battery (CR2032 3V). Then, open the front and back cases using a small flathead screwdriver. Remove the metal clips, remove the battery, and then replace it. After reassembling the fob, put the mechanical key back in position and ensure that it is working correctly. If it isn't then you'll need to take it to a Nissan dealer or a professional auto locksmith to repair the chip in the key. Fortunately, the chip is not often damaged by water exposure and therefore this shouldn't be a major expense.

Dead Coin Battery

The coin battery is a second common reason why your Nissan Qashqai remote key fob may not work. The batteries typically last for 3-5 years but can go bad over time, especially when the fob is dropped frequently. You can replace the battery with a new one but be sure it's the same voltage and size as the original. If you choose to use another battery, it may cause the key to have an incorrect key ID, which could prevent it from connecting to your vehicle.

The most efficient method to change the battery inside a Nissan Qashqai Key Fob is to open it with an incredibly small screwdriver. The screwdriver should be inserted into an angled notch on the bottom of the fob, and move it around to separate the two halves of the key fob. Then, remove the old CR2025 button cell battery and replace it with the new one after confirming its location in the fob.

Before putting the new battery in place, make sure there isn't any dirt or water damage to the terminals. If there is, wash the terminals with a tiny amount of isopropyl alcohol. You'll also need to make sure the pole cables are plugged in properly - they must be connected to the positive and negative poles of the battery.

Fault Diagnosis

If your Nissan Qashqai key fob stops working after exposure to pure rain or tap water, it may be an indication of a chip issue inside. Changing the battery won't fix this, and you'll need to buy the new key fob. If the key fob has stopped working after dropping it, it's likely that the chip inside was damaged. If you clean the chip with isopropyl alcohol and paper towel and then replace it with the key fob, it is possible to generally get it back to working.

Key ID Incorrect is a typical mistake that you might see on the dashboard of your vehicle. The vehicle is unable recognize the key fob, and consequently, won't allow the vehicle to start. The problem can be caused by many things like water damage, undetectable faults in the circuitry of the key fob or RFID interference.

The key fob won't work in the event that the batteries with 12 volts are dead or do not provide enough electrical current. This could affect your Nissan Qashqai's remote keyless system central locking, as well as the ability to start the engine with the key fob. If you are unable to lock or unlock the door by hand it is recommended to check the batteries inside your key fob to be sure they are in good shape. You may also try reconnecting the battery in order to reset your transmitter.

Reprogramming

If the key fob was not submerged into saltwater it should be restored to its original state with a simple rinse of clean water. You may also try cleaning the electronic chip with isopropyl alcohol or an electronic cleaner. If none of these works, it may be time to replace the entire key fob with a new nissan key one.

If your Nissan Intelligent Key is still not functioning, there may be an issue with the connection between it and your car. Start by turning the ignition key without activating the vehicle. Continue to do this until the hazard light flashes two times. Then, turn the car off and take out the keys.

Next, open the fob compartment of your vehicle. It's usually on the door jamb or the handle of the door for the driver. Find the small button labeled "program" and press it. You should hear a chime sound after the process has been completed.

Now that your Intelligent Key is relinked to the car is the time to test it out. You must stand a certain distance away from the vehicle, and press all the buttons on it. If the lights flash or the horn sounds, then the key is connected to the Nissan. You may also try testing the key in close proximity.