Repairs to uPVC Windows

uPVC is an excellent choice for modern homes. They are durable, long-lasting and easy to maintain. They are not susceptible to decay or rust as aluminum or timber.

Regularly cleaning and lubricating UPVC windows and doors is essential. This will prevent unnecessary repair costs and improve the efficiency of energy.

1. Broken Glass

If the glass in your window is broken it could cause a large amount of damage to your home, which can make it extremely dangerous and possibly fatal. You should take the time to ensure that your windows are in good condition.

For single pane windows it can be relatively simple to replace them, and the replacement will usually fit inside the frame that was previously installed easily. However, if you have double-pane windows that are secured by internal beading, it will be more difficult to remove the panes that are in place and replace them with new ones. In this situation you'll need to source some plastic spacers that will assist the new pane to fit properly into the frame of the window.

If you are going attempt to remove the window panes by yourself, it is essential to wear the proper safety gear such as gloves that are thick and eye protection. It is also recommended to lay down a drop cloth before you begin working on the glass to ensure that any shards fall onto the fabric instead of landing on the floor, where they could be trampled upon and cause further damage.

Once the glass is removed, it's a good idea to seal the gap with some clear packaging tape or duct tape to stop water and drafts from getting into the home until a professional comes out and fix the window. This will also act as a barrier, deterring any intruders to gain access to your home. If the gap is particularly large, you might be interested in a security door that has an integrated window as it will provide the best of both worlds.

2. Sagging

Upvc is a long-lasting energy-efficient, cost-effective and economical alternative to timber sash window. Over time, they can be affected by a variety of issues that include sliding. A sagging uPVC windows could cause issues with light, draughts and even security. It's important to take action when you realize that your upvc window repairs windows are falling down.

To fix a sagging window you can try repositioning the hinges. To do this, UPVC window repairs you'll need open the window so that you can get to the frame. Then, remove both the hinges on the top and bottom with a screwdriver and adjust them clockwise or counter-clockwise. Once you've adjusted the hinges, shut your window and test it for UPVC Window Repairs an appropriate fit. If you're satisfied with the size of the window, tighten the screws to hold them in the right position.

If you aren't able to move the hinges, you may need to replace the seal. Rubber seals may dry out and lose their elasticity with time, leading them to loose their elasticity. It is important to replace your seal as quickly as you can to ensure that your uPVC window watertight and draughtproof.

uPVC handles can also loosen up. Most often it is due to screws that have come loose over time. However, it can also happen because the handle mechanism has been worn out. Fortunately, it's easy to fix a loose uPVC window handle yourself. First, you'll need to shut the window and perform a test fitting. The corners of the sash must align with the casing joint. If it doesn't, you can use a screwdriver or a wrench to loosen the handle and then reverse the mechanism back into the position it was in.

3. Water Leaks

If you're waking up to wet floors and mouldy walls each time it rains it is important that you take action. The leaks of water from windows do can not only cause degrading of the structure of your home but also hinder your efforts to control the temperature within your home. Most of the time, uPVC window leaks are caused by damaged or missing sealant.

This is a fairly simple fix that can be done by any skilled DIYer. Depending on the severity of the issue the caulking used previously may need to be removed before a new layer is applied. It is essential to keep in mind that when it comes to uPVC window repairs you should avoid the temptation to "over-caulk in order to make the area more difficult to clean and could reduce your energy efficiency.

Verify that the drainage holes have no debris in them and that the sill pan has been properly angled to allow the water to drain from the window. In more serious situations, you may need to think about replacing the window.

Other indicators of long-term water leakage are rotted sills and the appearance of black spots of mold on the walls near the window. This mold thrives in damp environments and is able to quickly spread throughout the home.

If the leakage is occurring between the double-glazed window, it is more likely the issue is more with the seal rather than the frame. A uPVC specialist can easily fix this problem by replacing the glass seal. This will ensure the complete insulation of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or loose and blow open in a breeze, it may be the hinges that are at the fault. These are easily repaired by any skilled DIYer and can usually be completed in just a few minutes.

Most households in the UK will have either top hung or side hung uPVC windows that are hinged and like any mechanical part they will wear out over time. It is very easy to replace a hinge on a window, but it's easier if someone else helps you to hold the frame.

Make sure that the uPVC hinges are closed and open in the right direction. Check for the arrows on each hinge to determine the direction in which the window should be opened.

The issue can be caused either due to opening the window in the wrong way or due to a poor installation in the factory. It is usually possible to fix the issue by sending us a picture via our website and we will be more than happy to give you advice.

It is also crucial to grease the hinges regularly. This can be accomplished by applying a light engineering oil on the hinges, we recommend using a solvent-free lubricant, such as the 3-in-one Multi-Purpose oil. Regular lubrication can help the window open and close more easily. It can also prevent corrosion and reduce the risk of sticking. This should be done at least once a year. WD40 and other solvent based fluids are not recommended since they could damage parts of your uPVC window.

5. Draughts

Draughts can be caused by different factors. Firstly the hinges, again because of wear and tear, can become misaligned, this can cause gaps to develop between the sash and the frame. If they are damaged beyond repair, it could be required to realign them. The second is the interlock, which is located on the hinge of the window, may also become misaligned, again it is feasible to give them a thorough clean, however in some cases it might be necessary to get them replaced.

The next most common reason for draughts are the window seals, these can become worn down or damaged over time and allow air to escape through the gaps. Replacement of these with high-quality weatherstripping can help keep draughts at bay. Another option is to replace the upvc window with low-emissivity glass, this will help in regulating indoor temperatures, and also lessen the possibility of draughts.

The final method to cut down on drafts effectively is to use a Draught-excluder. These are usually made of fabric tubes filled with a filler, which can be placed over your window sill. They can help keep cold air out and keep your home warm and cosy!

The windows made of upvc can keep providing excellent insulation and security for your home with regular maintenance and repairs. It is essential to remember that all windows eventually become worn out, and it could be more cost-effective to simply replace them rather than repair them. So, if you are experiencing problems with your upvc repairs windows, it is always recommended to seek assistance from a professional as soon as you can.