Repairs to uPVC Windows

uPVC is an excellent choice for modern homes. They are easy to maintain, durable and long-lasting. Unlike timber and aluminium, they are not susceptible to get rusty or decay.

Regularly cleaning and lubricating UPVC windows and doors is essential. This will save you from costly repairs and improve energy efficiency.

1. Broken Glass

The damaged glass in your windows could cause serious damage to your home and may even be fatal. It is crucial to take the time to make sure that you are doing everything you can to ensure that your windows are in good condition.

Single-pane windows are fairly simple to replace and will usually fit into the frames of the past easily. However, if you have double-pane windows that are held in place by internal beading it will be more difficult to take out the existing panes and install new ones. In this situation, it is necessary to purchase plastic spacers in order to help the new pane fit into the window frame.

If you're planning to attempt to remove the window panes by yourself, it is essential to wear the proper safety gear such as gloves that are thick and protective eyewear. It is also recommended to lay down a drop cloth prior to when you begin working on the glass, so that any fragments of glass fall on the fabric rather than on the floor where they can be trodden under and cause further damage.

It's a great idea cover the gap with tape after the glass has been removed. This will stop drafts and double Glazing ramsgate water from entering your home until a professional comes out to fix the window. This will also act as a barrier that will prevent any intruders to gain access into your home. If the gap is particularly large, you might want to consider using a security door that has an integrated window, since this will offer the best of both worlds.

2. Sagging

uPVC windows and doors are an affordable, durable and energy-efficient alternative to timber sash windows. Over time, they can develop a number of problems such as sagging. A sagging window in uPVC can cause problems with light, draughts and even security. It's important to take action when you notice your uPVC windows are sliding.

To fix a window that is sagging you can try repositioning the hinges. To do this, you'll have to open the window so that you can access the frame. Then, using an screwdriver, unscrew the hinges on the top and bottom and adjust them by turning them clockwise or anti-clockwise. Close your window to check the fit after you have repositioned your hinges. If you're satisfied with the fit, you can tighten the screws to ensure that they stay in the right place.

If you can't reposition the hinges, you might need to replace the seal. Rubber seals may dry out and lose their elasticity with time, leading them to loosen. If this happens, it's important to replace the seal as fast as possible so that your uPVC windows remain watertight and secure from draughts.

uPVC handles could also become loose. This is typically caused by screws that have become undone over time, but it could also be caused by the handle mechanism wears out. Fortunately, it's easy to fix the loose uPVC window repairs Bromley handle yourself. The first step is to close the window and perform an experiment to ensure that it fits. The joint at the corners of the sash should be aligned with the joint on the casing. If it isn't then you can use a screwdriver to loosen the handle and then return the mechanism to its original position.

3. Water Leaks

It is important to take action if wake up every morning to discover mouldy walls and wet floors. The leaks of water through windows could cause structural damage to your home, and impact your ability to regulate the temperature inside your home. Most often, uPVC window leaks are caused by damaged or missing sealant.

This is a fairly simple fix that can be done by any skilled DIYer. Depending on the severity of the problem the caulking used previously may need to be removed before a fresh layer can be applied. When it is time to uPVC repair, you should be careful not to over-caulk. This can make your window more difficult to clean and lower its energy efficiency.

Make sure that the drainage holes have no debris in them, and also that the sill pan is properly angled to drain away from the window. In more severe instances, you may need to replace the window.

Mold spots and rotten sills are also signs of water leakage. This mold thrives in damp environments and can quickly spread across the house.

If the leakage occurs between the double glazing Bromley-glazed glass, it is more likely the problem is with the seal rather than the frame. Again this can easily be fixed by an uPVC window specialist who can replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

Hinges could be at fault for the reason that your uPVC window is difficult to open or it opens in the breeze. They can be repaired by any DIYer who is skilled and can usually be completed in just a few minutes.

Like all mechanical parts hinges will wear out over time. It is very easy to change the hinges on a window, but it's easier if someone helps you to hold the frame.

It is also worth checking that the uPVC hinges are opening and closed in the correct direction. You can check this by looking for the arrow on each hinge, this shows which way the window should be opened.

Window hinges that aren't working properly could be caused by improperly opening the window in a certain way or by poor installation at the factory. This can often be resolved by sending us a photograph on our website. We will be more than happy to give you suggestions.

Regular lubrication of the hinges is also necessary. This can be done by applying a light engineering oil on the hinges. We recommend using a solvent-free lubricant, such as the 3-in-one Multi-Purpose oil. Regular lubrication will make the window easier to open and close. It also decreases the risk of a window sticking and double glazing repair Ramsgate prevent corrosion. The ideal time to do this at least once a year. WD40 and other solvent-based lubricants should not be used since they could damage your uPVC windows.

5. Draughts

Draughts can be caused by several different causes. First, the hinges because of wear and tear, could become misaligned. This can cause a gap to form where the sash meets the frame. If they're beyond repair, it could be necessary to have them realigned. Second, the interlock can also become disaligned. It is located on the hinge side and may need to be cleaned. In certain instances it is possible to replace the hinges.

These seals are susceptible to wear and tear or become damaged over time, allowing air to escape. This can be prevented by replacing them with high-quality weatherstripping. Replace the upvc windows with low-emissivity glass. This will help control indoor temperatures and decrease draughts.

The final method to cut down on drafts effectively is to use a Draught-excluder. These are usually fabric tubes filled with a filler which can be hung over your window sill. They will keep your home warm by blocking out cold air.

With a little regular maintenance and repair your windows made of upvc will continue to provide a great level of insulation and security for your home. It is crucial to recognise that all windows have a lifespan and eventually, they will reach an point at which it is more economical to replace them than fix them. If you are having issues with your upvc windows, it is recommended to seek assistance from a professional as soon as possible.